There are multiple ways to communicate between Siemens WINCC6.0 and Siemens PLC. Below are two commonly used communication methods. 1、 The prerequisite for using a regular network card to communicate with the PLC through TCP/IP and connecting WICC6.0 to the PLC system through Ethernet is that the PLC system is configured with an Ethernet module or uses a PLC with a PN interface, such as CP443-1 or CP343-1, and a PLC with a PN interface, such as CPU 315-2PN/DP. The following is a communication connection using a regular network card CP443-1. 1. STEP7 Hardware Configuration Use STEP7 programming software to configure the hardware of the PLC system. Insert the actual PLC hardware into the "Hardware" configuration window, as shown in Figure 1: Figure 1 STEP7 Hardware Configuration 2. Double click CP443-1 ...

1. Fault code analysis method If the ABB frequency converter has a fault, there are corresponding fault codes on the operation panel. Generally, when dealing with frequency converter faults, it is necessary to find its fault code on the operation panel and conduct a deeper analysis based on the fault code. Based on my personal experience in frequency converter maintenance and some common fault codes, I will briefly discuss some common fault handling methods. 1.1 Fault code: BRAKEFLT Reason for malfunction: Brake failure, brake opening timeout or brake not opening properly. Solution: Open the cover of the brake on site, forcefully open the brake coils in the program, observe the limit opening status of the brake, and if the brake cannot be opened or the mechanism is stuck, replace the brake; If the distance between the limit opening and the limit sensing piece is far...

(1) Fault 1: Touch deviation Phenomenon 1: The position touched by the finger does not coincide with the mouse arrow. Reason 1: After installing the driver program, there was no vertical touch on the center position of the bullseye during calibration. Solution 1: Recalibrate the position. Phenomenon 2: Some areas have accurate touch, while others have deviation in touch. Reason 2: The accumulation of a large amount of dust or scale on the surface acoustic wave reflection stripes around the surface acoustic wave touch screen affects the transmission of acoustic signals. Solution 2: Clean the touch screen, paying special attention to cleaning the sound wave reflection stripes on all sides of the touch screen. When cleaning, disconnect the power supply of the touch screen control card. (2) Fault 2: Touch screen does not respond to touch Phenomenon: When touching the scree...

Operation content: Establish communication between the touch screen and PLC to enable the touch screen to read and write PLC data Communication method: Touch screen communicates with PLC through DP Download line: USB/PPI Precautions for operation: Firstly, in STEP 7, perform hardware configuration (without attaching the HMI as a slave to the PROFIBUS bus, as the HMI is a secondary master), set the DP address and baud rate Then, set the connection parameters in the touch screen programming software (note that the connection parameters should be consistent with those in STEP 7) Finally, transfer the touch screen program to the touch screen via a download cable After successful transmission, it indicates that the program has been successfully downloaded to the touch screen  ...

Operation content: Establish communication between the touch screen and PLC to enable the touch screen to read and write PLC data Communication method: Touch screen communicates with PLC through DP Download line: USB/PPI Precautions for operation: Firstly, in STEP 7, perform hardware configuration (without attaching the HMI as a slave to the PROFIBUS bus, as the HMI is a secondary master), set the DP address and baud rate Then, set the connection parameters in the touch screen programming software (note that the connection parameters should be consistent with those in STEP 7) Finally, transfer the touch screen program to the touch screen via a download cable After successful transmission, it indicates that the program has been successfully downloaded to the touch screen  ...

Regarding the issue of not being able to read the value, if there is always no change in 32767, the value already exists, it is just an overrange. If the value is 0, then attention should be paid to whether there is a problem with the analog quantity. Using a multimeter to measure the on-site signal does not exceed the limit. Why do these two phenomena occur? This is because the selected reference potential is different. For example, if the signal coming from the site is 5V, the first thing to ask is what voltage is the reference point? 10-15 is 5V, and -10~-5 is also 5V. If the reference point of the measuring end is 0V, there will be a problem with the measurement, so it is necessary to ensure that both ends are equipotential. The reference potential point of the analog module is MANA, and all wiring is related to it. 02Isolation and Non Isolation Issues Series Th...

★: For faults that cannot be reset automatically, the cause of the fault must be cleared by turning it off and then on before resetting ▲: After the cause of the fault disappears, the fault can be reset using the automatic restart function. These faults can also be re powered on through the frequency converter or reset through logic input or control bits ●: A fault that can be reset as soon as the cause disappears. Serial number fault code fault name possible cause repair measures 1 ANF ★ Load Encoder speed feedback does not match the given value 1. Check the motor, gain, and stability parameters 2. Add a braking resistor 3. Check the size of the motor/frequency converter/load 4. Check the mechanical connection and wiring of the encoder 2 BRF ★ Mechanical brake failure The brake feedback contact is inconsistent with the brake logic 1. Check the feedback circuit a...

1. Bit operation instructions: Bit operation instructions are used to read, write, and modify bit level data. Common bit manipulation instructions include LD (logical AND), ORR (logical OR), AND (logical AND), XOR (XOR), etc. 2. Data operation instructions: Data operation instructions are used to read, write, and modify byte, word, and doubleword level data. Common data operation instructions include MOV (assignment), ADD (addition), SUB (subtraction), MUL (multiplication), DIV (division), etc. 3. Counter instruction: Counter instruction is used to implement counting function. There are three types of counter instructions: rising edge counter, falling edge counter, and stage counter. The counter instruction can be used for applications such as quantity statistics and progress monitoring. 4. Timer instruction: The timer instruction is used ...